C553 Standard Specification for Mineral Fiber
The ASTM Products are also available in Adobe Acrobat (PDF) format to Licensee and its Authorized Users, who are solely responsible for installing and configuring the appropriate Adobe Acrobat Reader software. ... C. ASTM shall use reasonable efforts to make online access available on a continuous basis. Availability will be subject to …
C633 Standard Test Method for Adhesion or Cohesion
1.3 This test method is limited to testing thermal spray coatings that can be applied in thickness greater than 0.015 in. (0.38 mm). The limitation is imposed because an adhesive bonding agent is used in the test. Those bonding agents established so far for this method tend to penetrate thermal spray coatings and may invalidate results unless the …
C1240 Standard Specification for Silica Fume Used
Scope. 1.1 This specification covers silica fume for use in concrete and other systems containing hydraulic cement. 1.2 In the cases of slurried or densified silica fume, perform the tests on the raw silica fume from which these products have been made. 1.3 The units stated in SI are to be regarded as the standard.
ASTM | المواصفات القياسية للجمعية الأمريكية للإختبار والمواد كاملة
تحميل جميع المواصفات الفياسية للجمعية الأمريكية للإختبارات والمواد ASTM Standards بأحدث نسخه لها نسخة 2018 | ASTM 2018 وكذلك نسخة 2015 | ASTM 2015, مواصفات الجمعية الأمريكية للاختبارات والمواد كاملة, تحميل مواصفات ASTM كامله PDF, Download All ASTM ...
Standard Specification for Ready-Mixed Concrete1
2.1 ASTM Standards:3 C 31/C 31M Practice for Making and Curing Concrete Test Specimens in the Field C33Specification for Concrete Aggregates C 39/C 39M Test Method for Compressive Strength of Cy-lindrical Concrete Specimens C 125 Terminology Relating to Concrete and Concrete Aggregates C 138/C 138M Test Method for Density …
C33 Standard Specification for Concrete Aggregates
Scope. 1.1 This specification defines the requirements for grading and quality of fine and coarse aggregate (other than lightweight or heavyweight aggregate) for use in concrete. 1.2 This specification is for use by a contractor, concrete supplier, or other purchaser as part of the purchase document describing the material to be furnished. Note ...
C109/C109M Standard Test Method for Compressive
Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) C0109_C0109M-20 ASTM|C0109_C0109M-20|en-US Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) Standard …
C39/C39M Standard Test Method for Compressive
Scope. 1.1 This test method covers determination of compressive strength of cylindrical concrete specimens such as molded cylinders and drilled cores. It is limited to concrete having a density in excess of 800 kg/m 3 [50 lb/ft 3 ]. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard.
March 2020
representing 150 countries, ASTM publishes more than 12,000 standards each year in the 85 volumes of the An-nual Book of ASTM Standards and on-line products. These standards and related information are distributed and used worldwide. The basic organization of ASTM is illustrated in FIGURE 1 . Board of Directors
C1289 Standard Specification for Faced Rigid
Scope. 1.1 This specification covers the general requirements for faced thermal insulation boards composed of rigid cellular polyisocyanurate surfaced with other materials. The insulation boards are intended for use at temperatures between −40 and 200°F (−40 and 93°C). This specification does not cover cryogenic applications.
C1609/C1609M Standard Test Method for Flexural
Note 5 — The results obtained using one size molded specimen may not correspond to the performance of larger or smaller molded specimens, concrete in large structural units, or specimens sawn from such units. This difference may occur because the degree of preferential fiber alignment becomes more pronounced in molded specimens …
(PDF) ASTM C150 | Sebastian Nicolalde
Esta norma en español está basada en la norma ASTM C 150-07, Especificación Normalizada para Cemento Portland1,2007, esta norma está protegida por los derechos de autor de la ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428, USA. Traducida y reimpresa según el acuerdo de licencia con ASTM International.
Standard Specification for Elastomeric Joint Sealants
Abstract. This specification covers the properties of a cured single- or multicomponent cold-applied elastomeric joint sealant for sealing, caulking, or glazing operations on buildings, plazas, and decks for vehicular or pedestrian use, and types of construction other than highway and airfield pavements and bridges.
C109/C109M Standard Test Method for Compressive
Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50 mm] Cube Specimens) C0109_C0109M-21 ASTM|C0109_C0109M-21|en-US Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50 mm] Cube Specimens) Standard …
Standard Specification for Ready-Mixed Concrete
Fiber-reinforced concrete is covered in Specification C1116/C1116M. 1.2 As used throughout this specification the manufacturer produces ready-mixed concrete. The purchaser buys ready-mixed concrete. 1.3 The values stated in either SI units, shown in brackets, or inch-pound units are to be regarded separately as standard.
Standard Terminology Relating to Thermal Insulation
Scope. 1.1 This standard provides definitions, symbols, units, and abbreviations of terms used in ASTM standards pertaining to thermal insulating materials, and to materials associated with them. 1.2 This terminology is not intended to be used to classify insulation materials as having particular properties.
C150 Standard Specification for Portland Cement
Scope. 1.1 This specification covers eight types of portland cement, as follows (see Note 2): 1.1.1 Type I - For use when the special properties specified for any other type are not required. 1.1.2 Type IA - Air-entraining cement for the same uses as Type I, where air-entrainment is desired. 1.1.3 Type II - For general use, more especially when ...